OWNER’S MANUALNatural Sound AV ReceiverR-V902Thank you for selecting this YAMAHA AV receiver.A
10CONNECTING SPEAKERSMAIN CENTER REAR(SURROUND)OUTPUTSUBWOOFERREAR(SURROUND)CENTERCDDUALSINGLECAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. MA
11For connecting to the MAIN SPEAKERS terminalsRed: positive (+)Black: negative (–)➀Unscrew the knob.➁Insert the bare wire.[Remove approx. 5mm(1/4”)
12MAIN OUTPUT terminalsThese terminals are for main channel line output. There is noconnection to these terminals when you use the built-inamplifier
13ANTENNA CONNECTIONS●Each antenna should be connected to the designated terminals correctly, referring to the following diagram.●Both AM and FM indo
1 POWER switchPress this switch to switch the power on. Press it again toswitch the power off.2 Standby mode indicator (Except U.S.A. and Canada mode
A SPEAKERS switchesSet the switch A or B (or both A and B) for the main speakersystem (connected to this unit) you will use to the ON position.Set the
1 Multi-information displayDisplays various information, for example station frequency,preset station number and name of selected input source.2 STERE
1Set to the “∞” position.2 Turn the power on.3 Select the main speakers to be used.* If you use two main speaker systems, press both the Aand B switch
18l620284060l28420–dB7 Select the center channel output mode suitable for yourspeaker configuration.(Refer to “SPEAKER CONFIGURATION” on page 6.)On t
1910 Adjust the sound output levels of the centerspeaker and the rear speakers so that theybecome almost as same as that of the mainspeakers.a) Press
2After unpacking, check that the following parts are included.Supplied Accessories ...2Features ...
1Set to the “∞” position.2 Turn the power on.3 Select the desired input source by using the inputselector buttons.(For video sources, turn the TV/moni
211 Select the source to be recorded.2 Play the source and then turn the VOLUME control upto confirm the input source. (For detailed informationon t
Selecting the SPEAKER systemBecause one or two speaker systems (as main speakers) canbe connected to this unit, the SPEAKERS switches allow youto sele
231 Select the reception band (FM or AM) confirming it onthe display. 23 Tune to a desired station manually. * To continue tuning search, press and ho
1 Tune to a desired station.(Refer to the previous page for tuning procedure.)2 Select a desired group (A – E) of preset stationsconfirming it on the
25123To tune to higher frequencies, press right side once.To tune to lower frequencies, press left side once.* If the TUNING button is not pressed, in
1 Recall the preset station on E1 (by following the methodof “To recall a preset station” on page 24).23 Next, recall the preset station on A5 by foll
27Brief Overview of Digital Sound Field ProgramsThe following list gives you a brief description of the sound fields produced by each of the DSP progr
1 Follow steps 1 – 6 shown in “BASIC OPERATIONS” onpage 20.2 Select the desired program that is suitable for thesource.The selected program name is sh
29Adjustment of the CENTER LEVELTIME/LEVELDELAY/CENTER/REAR/SWFRAdjustableAdjustment of the REAR LEVELIf desired, you can adjust the sound output leve
3●5 Speaker ConfigurationMain: 90W + 90W (8Ω) RMS OutputPower, 0.07% THD, 1 kHzCenter: 90W (8Ω) RMS Output Power, 0.07% THD, 1 kHzRear: 35W + 35W (8
30Adjustment of DELAY TIMEYou can adjust the time difference between the beginning ofthe sound from the main speakers and the beginning of theeffect s
1Whenever the SLEEP key is pressed, the SLEEP time willchange as follows.After a while, the display returns to the indication beforethe SLEEP timer is
32BASIC OPERATIONS (When the lid is open)The remote control transmitter provided with this unit is designed to control all the most commonly used func
33RESET button1 Tape deck keysControls tape deck.(The A/B/C switch (E) should be set to the “A” position.)* DIR A, B and A/B are applicable only to do
34LEARNING NEW CONTROL FUNCTIONS (When the lid is open)This is a learning remote control transmitter. The shaded keys in the illustration shown below
35TAPEACDTUNERVCRBDVD/LDV-AUXPHONOEFFECTON/OFFTV/DBSCDIRTRANSMIT/LEARNLEARNCLEAR MACROPRESETA/B/C/D/EPRO LOGIC ENHANCED123MOVIESTADIUMDISCOMONOVIDEOCO
36When the lid is closed, the OPERATION CONTROL keyssubstitute for the keys numbered 1, 2, 3 and the (+10)key on the left illustration. To use these
37REMOTE CONTROLTRANSMITTERTAPECDTUNERVCRDVD/LDV-AUXPHONOTV/DBSTVVCROFFSYSTEMPOWERMASTERVOLUMEOPERATIONCONTROLEFFECTTRANSMITMACROQUICKOFFSLOWTAPEACDTU
38Macro key1st(Turning the power of this unit on)2nd(Selecting an input source)3rd(Playing a source)“”on area A of keys 1“”on area A of keys 2–“”on ar
39LEARNING A NEW FUNCTION1 Place this remote control transmitter and the otherremote control transmitter so that they face each other.2* If there is n
41. To assure the finest performance, please read this manualcarefully. Keep it in a safe place for future reference.2. Install this unit in a cool,
401* If there is no operation for about 30 seconds after theMACRO button is pressed, the TRANSMIT/LEARNindicator flashes rapidly and the mode before y
411 To clear a learned key function, press the LEARN buttonusing the point of a mechanical pencil, etc.To clear a macro you made, press the MACRO butt
42Battery installationBattery replacementIf you find that the remote control transmitter must be usedcloser to the main unit, the batteries are weak.
43GeneralFMAMRemote controltransmitterIf the unit fails to operate normally, check the following points to determine whether the fault can be correcte
AUDIO SECTIONMinimum RMS Output Power per ChannelMain L, R8 ohms, 1 kHz, 0.07% THD...90W + 90WCenter8 ohms, 1 kHz, 0.07% THD ...
5PROFILE OF THIS UNITYou are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound FieldProcess
6SPEAKER SETUPSPEAKERS TO BE USEDThis unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective sp
7CONNECTIONSNever plug in this unit and other components until all connections are completed.CONNECTIONS WITH OTHER COMPONENTSWhen making connections
8AC OUTLET(S) (SWITCHED)[U.S.A., Canada and General models]..... 2 SWITCHED OUTLETS[Australia mode
9Connecting with a Dolby Digital (AC-3) DecoderIf you have a Dolby Digital (AC-3) Decoder unit or an LD player etc. which incorporates a Dolby Digita
Komentarze do niniejszej Instrukcji