Yamaha CRW6416S Series Instrukcja Właściciela

OWNER’S MANUALBEDIENUNGSANLEITUNGMODE D'EMPLOIMANUAL DE INSTRUCCIONESCD-R/RW DriveCRW6416SSERIESOWNER’S MANUALBEDIENUNGSANLEITUNGMODE D’EMPLOIMAN

3System ConfigurationIn order to use the CRW6416S drive, your computer system will need to meetthe following set of requirements.ComputerThe minimum s

4MediaThe CRW6416S drive is compatible with discs which meet the followingspecifications:● CD-R discs:Use discs that conform to the Orange Book Part 2

5ToolsYou will need the following tools at hand when installing the CRW6416S drive.Philips ScrewdriverYou will need to use this when removing the cove

6Front and Rear of UnitFront PanelThe CRW6416S drive’s front panel features the following:Disc trayThe tray is used to hold the disc. It slides out f

7Rear PanelThe CRW6416S drive’s rear panel features the following:AUDIO OUTID SELECTPARITYTERMINATORBLOCK SIZESCSIINTERFACECONNECTORDC INPUT1+5V G+12V

InstallationThis section gives a step-by-step guide to installing the CRW6416S drive. Makesure you have all the necessary tools.First StepsOnce you h

To set each jumper switch, you have to bridge the two pins in the respectivecolumn of the grid with a plastic shunt. Shunts are already attached to t

1 SCSI ID numberEach of the SCSI devices connected to the computer is identified by its SCSI IDnumber. You need to assign a number from “0” to “7” fo

11Installation2 Parity CheckThe parity check is used for error correction during data transmissions. Ifparity-checking has to be disabled, the shunt

124 Block SizeThe data block size of the CRW6416S can be set to 512 bytes per sector bysetting the Block Size jumper switch to “on.” This is necessar

FCC INFORMATION (U.S.A.)1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this m

Installing the CRW6416S DriveYou can install the CRW6416S drive in one of two possible ways:● As an additional driveIf the casing of your computer has

14Fitting the CRW6416S as an Additional Drive1 Power down your computer and unplug it from the AC outlet.If you proceed without doing this, you run th

3 Touch a metal part of the computer’s chassis or power supply unit to drainany static charge that may have built up inside your body.You can permanen

5 Leave enough room behind the drive for connecting the power, SCSI andaudio cables. Then tighten the four fastening screws on the sides of the unitb

Installation7 Connect one end of the 50-pin SCSI flat cable to the computer’s SCSI adapter card.Align the red line of the cable with Pin 1 of the card

8 Connect the audio cable between the CRW6416S drive and the computer’ssound card, or the motherboard’s audio connector if it has built-in audio.One e

19Installation9 Connect a 4-pin power cable to the power supply connector of theCRW6416S marked “DC INPUT.”n There may be more than one 4-pin power ca

! Attach the outer casing of the computer and any screws that were removed.@ Reconnect the computer to the AC outlet and power it up.n When you power

#After the computer’s operating system has loaded, open the Control Panel anddouble-click on the System icon. Select the Device Manager tab and doubl

22Replacing an Existing CD-ROM Drive with the CRW6416Sn The existing CD-ROM drive in the computer is assumed to be an IDE-type.1 Power down your compu

CD-R/RW DriveCRW6416SSERIESCD-R/RW DriveCRW6416SSERIESOWNER’S MANUALEnglishi6416S_e15.qx 6/29/99 6:00 PM Page 3

3 Touch a metal part of the computer’s chassis or power supply unit to drainany static charge that may have built up inside your body. You can perman

5 Remove the four screws holding the CD-ROM drive in place, then slide thedrive forward and out from the drive bay.Slide the CRW6416S drive backwards

7 Remove the SCSI adapter card from the computer and turn its terminationOFF so that internal SCSI devices may be connected. Refer to thedocumentatio

8 Connect one end of the 50-pin SCSI flat cable to the computer’s SCSI adapter card.Align the red line of the cable with Pin 1 of the card’s SCSI conn

27Installation9 Connect the audio cable between the CRW6416S drive and the computer’ssound card, or the motherboard’s audio connector if it has built-

28) Connect the 4-pin power cable to the power supply connector of theCRW6416S marked “DC INPUT.”n There may be more than one 4-pin power cable availa

29Installation@ Attach the outer casing of the computer and any screws that were removed.# Reconnect the computer to the AC outlet and power it up.n W

$After the computer’s operating system has loaded, open the Control Panel anddouble-click on the System icon. Select the Device Manager tab and doubl

OperationThis section explains how to operate the CRW6416S drive after you haveinstalled it.Loading a Disc1 Press the Eject button on the CRW6416S dri

32n The disc tray will not open if the computer is not switched on. Also, depending on the SCSIadapter card settings, it may not open if the drive is

SAFETY PRECAUTIONSPLEASE READ CAREFULLY BEFORE PROCEEDINGThese precautions explain how to use the device correctly and safely, thereby preventing inju

33TroubleshootingPlease also refer to the Yamaha web site for more information.Yamaha web site URL: http://www.yamaha.co.jp/english/product/computer/T

34● Is the terminator on the CRW6416S drive set correctly? It should be set to ON only if it is the last device on the SCSI chain. Otherwise,it shou

35The drive ejects or fails to read the disc, or the ON/DISC LEDcontinues to blink in orange after the disc has been loaded(meaning that the disc has

AppendixWriting ModesDisc-at-Once (DAO)This mode is used when writing a complete disc in a single pass withoutpausing. Data cannot be added later, ev

Session-at-Once (SAO)This mode is used when writing each session in a single pass without pausing. Moresessions can be added later if there is enough

Determining the firmware version of the CRW6416S drive (in Windows 95/98)Go to Control Panel | System | Device Manager tab, double-click on CDROM, the

39CRW6416S SpecificationsSupported Write/Read Format CD-DACD-ROMCD-ROM XACD-ICD-BridgeCD ExtraVideo CDNote) Excludes ADPCM Encode/Decode & VideoE

Sector Size 2048 ~ 2352 B512 B (read only)Interface SCSI-2 (Fast SCSI)Installing style HorizontalDisc Loading Type Tray loadingAudio Out Line OutFrequ

41Index4-pin power cable ...19, 28AActive Desktop ...35additional drive...

Distributors and Head Offices / Bertrieb und HauptgeschŠftsstelle Distributeurs et si•ges sociaux / Distribuidores y Casas matricesIf you have any que

CAUTIONAlways follow the basic precautions listed below to avoid the possibility of physical injury toyou or others, or damage to the instrument or ot

XW387B0

About CD-R/RW discsPlease read the following regarding the handling of CD-R/RW discs.1. Do not expose discs to excessive heat or vibrations or extre

©1999 Yamaha Corporation. All Rights Reserved.This document may not, in whole or in part, be copied, photocopied,reproduced, translated, transmitted o

1Setup FlowchartThis flowchart shows the procedure for setting up the CRW6416S drive. Foreasy cross-referencing, the relevant pages in this manual ar

2IntroductionFeatures of the CRW6416S Drive6X Speed Writing to CD-R, 4X Speed Writing to CD-RW and 16XSpeed ReadingThe CRW6416S drive can write to CD-