Yamaha DME-N Remote Control Protocol Dokumentacja Pobierz pdf (Strona 3)

1.2 Remote Controller Setting

The Remote Controller settings for each connection are indicated as below.

Settings for control via the REMOTE connector

Baud Rate : 38400 bps

Data : 8bit

Parity : none

Stop Bit : 1bit

Flow Control : none

Settings for control via Ethernet (the NETWORK connector; not supporting DME64N/24N V3.5 or earlier)

IP Address: Specify the IP address of the DME Satellite to be controlled.

IP Poｒｔ No.: S

ecif

the IP Port No. that is set to the DME Satellite to be controlled.

1.3 DME Setting

The DME series settin

s for connection via the both connector are indicated as below.

1.3.1. DME series V3.8 or later

To dis

the setu

window

From DME Desi

From the DME

anel dis

(

onl

for DME64N/24N

)

To set the

arameter values

For control via the REMOTE connector

Select "Remote

(

RS-232C

)

" to control the DME via the RS-232C connection.

Select "Remote

(

RS-422

)

" to control the DME via the RS-422 connection.

For control via Ethernet

(

the NETWORK connector

)

Select "Network".

1.3.2. DME64N/24N V3.5 or earlier

(

not su

ortin

the control via Ethernet

)

To dis

the setu

window

From DME Desi

From the DME

anel dis

To set the

arameter values

Select "Remote Ctrl

(

232C

)

" to control the DME via the RS-232C connection.

Select "Remote Ctrl

(

422

)

" to control the DME via the RS-422 connection.

1.3.3. DME Satellite V3.5 or earlier

To dis

the setu

window

To set the

arameter values

For control via the REMOTE connector

Select "Remote Ctrl

(

232C

)

" as the Remote

arameter to control the DME via the RS-232C connection.

Select "Remote Ctrl

(

422

)

" as the Remote

arameter to control the DME via the RS-422 connection.

For control via Ethernet

(

the NETWORK connector

)

Check the checkbox for

[

Remote Control via Ethernet

]

The DME series can be controlled from an external device via the REMOTE connector or Ethernet (NETWORK connector; not

supporting DME64N/24N V3.5 or earlier).

The DME series can be controlled from an external device via the REMOTE connector or Ethernet (NETWORK connector; not

supporting DME64N/24N V3.5 or earlier).

Hold down the [Utility] button for three seconds to show the Utility display, then press the [Utility] butto

eatedl

until the Misc

e is shown. On the

e, select the Remote

arameter.

After going online between DME Designer and the DME series, open the [Hardware] menu -> [Utility] -> [Misc]

e of DME Desi

ner.

Generally the IP Port No. does not have to be set. However, it needs to be changed when the network consists of

another network device than the DME series and the network device has the same IP Port No. as the DME

series. Changing the port automatically resets the network connection on the DME, which means that DME

Designer needs to be restarted.

After going online between DME Designer and the DME series, open the [Hardware] menu -> [Utility] -> [Remote]

e of DME Desi

ner, then set the DME Remote Control

arameter.

Hold down the [Utility] button for three seconds to show the Utility display, then press the [Utility] butto

eatedl

until the Remote

e is shown. On the

e, set the Rmt Ctrl

arameter.

For only the DME Satellite, set the DIP switch (leftmost) on the rear panel to "RS-232C" (up) or "RS-422" (down)

while the

ower is off as well. If the settin

is chan

ed, the DME Satellite needs to be restarted.

Set the DIP switch (leftmost) on the rear panel to "RS-232C" (up) or "RS-422" (down) while the power is off as

well. If the settin

is chan

ed, the DME needs to be restarted.

After going online between DME Designer and the DME series, open the [Hardware] menu -> [Utility] -> [Misc]

e of DME Desi

ner, then set the Remote

arameter.

Generally the IP Port No. does not have to be set. However, it needs to be changed when the network consists of

another network device than the DME series and the network device has the same IP Port No. as the DME

series. Changing the port automatically resets the network connection on the DME, which means that DME

Designer needs to be restarted.

DME Remote Control Protocol Specifications V3.1

1 2 3 4 5 6 7 8 ... 22 23

Komentarze do niniejszej Instrukcji

Brak uwag

Yamaha DME-N Remote Control Protocol Dokumentacja Strona 3

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Nie Yamaha DME-N Remote Control Protocol